Arduino: Analog Read Serial - Revision history

Onnowpurbo: /* Code Indonesia */

2022-02-08T22:05:43Z

Code Indonesia

Onnowpurbo: /* Code */

2022-02-08T22:05:24Z

Code

Onnowpurbo: New page: Sumber: https://www.arduino.cc/en/Tutorial/AnalogReadSerial ==Hardware Required== * Arduino / Genuino Board * 10k ohm Potentiometer ==Rangkaian== [[Image:AnalogReadSerial BB.png|cen...

2015-12-04T02:28:59Z

New page: Sumber: https://www.arduino.cc/en/Tutorial/AnalogReadSerial ==Hardware Required== * Arduino / Genuino Board * 10k ohm Potentiometer ==Rangkaian== [[Image:AnalogReadSerial BB.png|cen...

New page

Sumber: https://www.arduino.cc/en/Tutorial/AnalogReadSerial

==Hardware Required==

* Arduino / Genuino Board
* 10k ohm Potentiometer

==Rangkaian==

[[Image:AnalogReadSerial BB.png|center|200px|thumb]]

[[Image:AnalogReadSerial sch.png|center|200px|thumb]]

==Code==

/*
AnalogReadSerial
Reads an analog input on pin 0, prints the result to the serial monitor.
Graphical representation is available using serial plotter (Tools > Serial Plotter menu)
Attach the center pin of a potentiometer to pin A0, and the outside pins to +5V and ground.

This example code is in the public domain.
*/

// the setup routine runs once when you press reset:
void setup() {
// initialize serial communication at 9600 bits per second:
Serial.begin(9600);
}

// the loop routine runs over and over again forever:
void loop() {
// read the input on analog pin 0:
int sensorValue = analogRead(A0);
// print out the value you read:
Serial.println(sensorValue);
delay(1); // delay in between reads for stability
}

==Referensi==

* https://www.arduino.cc/en/Tutorial/AnalogReadSerial

@@ Line 45: / Line 45: @@
 ==Code Indonesia==
-/*
+ /*
-  AnalogReadSerial
+   AnalogReadSerial
-  Baca analog input di pin 0, prints hasil ke serial monitor.
+   Baca analog input di pin 0, prints hasil ke serial monitor.
-  Kita dapat menyambungkan pin tengah potensiometer di pin A0, dan dua (2) lainnya ke +5V  dan ground.
+   Kita dapat menyambungkan pin tengah potensiometer di pin A0, dan dua (2) lainnya ke +5V  dan ground.
+ */
 void setup() {

← Older revision		Revision as of 22:05, 8 February 2022
Line 43:		Line 43:


		+	==Code Indonesia==
		+
		+	/*
		+	AnalogReadSerial
		+	Baca analog input di pin 0, prints hasil ke serial monitor.
		+	Kita dapat menyambungkan pin tengah potensiometer di pin A0, dan dua (2) lainnya ke +5V dan ground.
		+
		+	*/
		+
		+	void setup() {
		+	// serial monitor via USB pada kecepatan 9600bps
		+	Serial.begin(9600);
		+	}
		+
		+	void loop() {
		+	// baca analog pin A0:
		+	int sensorValue = analogRead(A0);
		+	// kirim nilai ke serial monitor
		+	Serial.println(sensorValue);
		+	delay(1); // delay antar read
		+	}

	==Referensi==		==Referensi==

	* https://www.arduino.cc/en/Tutorial/AnalogReadSerial		* https://www.arduino.cc/en/Tutorial/AnalogReadSerial